Brakes

Parts are being added to our catalogue regularly, please contact us should you need something you can't find here.

GWC127MS front L/H wheel cylinder

Front L/H 15/16" wheel cylinder for twin leading shoe brakes.

Sold individually, there are two cylinders on each front brake back plate.

NZ$ 34.00
GWC126MS front R/H wheel cylinder

Front R/H 15/16" wheel cylinder for twin leading shoe brakes.

Sold individually, there are two cylinders on each front brake back plate.

NZ$ 34.00
114713 Brake caliper piston, 8.4" brakes

Brake caliper piston for 8.4" solid rotor calipers. Made from stainless steel to eliminate corrosion often found on original chromed pistons. Sold each, two required per caliper.

NZ$ 35.00
Back Order

11K9181 Front brake pipe to subframe clip

Special clip used to secure the brake pipe that crosses the front of the front subframe.

NZ$ 2.75

Backorder
13H3735 Brake lamp switch

Brake pressure switch fitted to pedal box from late 70's. Can be retro fitted to earlier cars as the switch is much more reliable than the earlier hydraulic type.

NZ$ 15.00
Back Order

13H5541 Handbrake lever grip

Handbrake lever cover. Slide on cover, fits all leavers giving a more comfortable grip

NZ$ 15.00

Backorder
14A6733 Master cylinder base plate for single line master cylinders

Master cylinder base plate & bracket for engine stabiliser. This is for cars fitted with a single circuit brake master cylinder. Use with NAM9197 gasket. See ALA6505 for cars fitted with tandem master cylinders.

NZ$ 48.00
17H7612 Handbrake lever boot on rear backplate

Rubber boot to seal handbrake lever entry into backing plate. Fits both sides.

NZ$ 9.00
17H7620 Rear brake adjuster set

These rear brake adjusters will wear and become less adjustable over time. The result will be excessive pedal travel. This adjuster kit for drum brakes contains one adjuster screw and a pir of wedges wedges to repair one rear backplate.

NZ$ 67.50
17H7679 8.4" caliper transfer seal

This small internal seal must be replaced if the caliper halves are separated. For original 2-piston caliper as fitted to all cars after 1984. Sold each, use one per caliper.

NZ$ 3.50
17H7949 Wheel cylinder circlip

Spring circlip to attach rear wheel cylinder to the brake backing plate

NZ$ 2.00
17H8764 7.5" caliper transfer seal

This small internal seal must be replaced if the caliper halves are separated. For Cooper S, 7.5" calipers. Sold each, use one per caliper.

NZ$ 13.00
21A1270 Cooper S drive flange

Drive flange for Cooper S disc brakes. Attaches to rotor with SF604051 screws. Sold singly

NZ$ 90.00
Back Order

21A1774 Rear brake proportioning valve MK1/2 and Cooper S MK3

Rear brake proportioning valve MK1/2 and Cooper S MK3. This valve regulates the flow of fluid to the rear brakes under heavy braking. The front brakes do most of the work during braking, this valve controls the rears preventing brakes from locking up. This prevents loss of control if braking while turning.

NZ$ 195.00

Backorder
21A2031 Rear brake proportioning valve MK3

Mk3 rear brake proportioning valve. This valve regulates the flow of fluid to the rear brakes under heavy braking. The front brakes do most of the work during braking, this valve controls the rears preventing brakes from locking up. This prevents loss of control if braking while turning.

NZ$ 195.00
21A2064 Classic wheel stud, standard length (35mm)

This is the most common wheel stud used front and rear of all early Classic Mini and Mini Cooper before the change to wide rear drums. These fit most front disk brake cars too, and allow the use of MOST aftermarket wheels when used WITHOUT wheel spacers. Overall length 1.5" (35mm). Length of shaft, not counting head, 1.375". Threaded portion approx. .875"

NZ$ 4.80
21A2695 Drive flange for 8.4" solid rotor

Drive flange for 8.4" solid rotor as fitted to 1275GT and later Rover minis. Sold singly

NZ$ 95.00
21A385 Handbrake cable fairlead seal

Small rubber seal fits under the cable fairlead plate (ACA5522) to seal dirt and water from entering the cable hole(s). Sold singly

NZ$ 4.00
27H4656MS RH 7.5" brake caliper

New right-hand brake caliper for 7.5" Cooper S brakes

NZ$ 260.00
27H4657MS RH 7.5" brake caliper

New left-hand brake caliper for 7.5" Cooper S brakes

NZ$ 260.00
2A4295 Drive flange spacer

Drive flange spacer for drum brake minis and 997/998 Coopers. Fits between drive flange and outer hub bearing. Sold singly

NZ$ 15.00
2A5858 Handbrake adjusting nut - twin cables

Cable adjusting nut for pre 1976 Minis with twin handbrake cables. Sold each

NZ$ 13.75
2K8686 Brake & clutch hose retaining nut

Retaining nut for front brake & clutch flexi hoses

NZ$ 5.00
31G279 Master cylinder gasket

Master cylinder gasket for single line master cylinders. Fits clutch and brake, sold singly

NZ$ 3.80
31G5049 Handbrake cable adjuster nut, MK4 on

Handbrake adjustment nut on the forward cable of 1976-on cars with single cable systems

NZ$ 12.00
31G840 Dual-circuit master cylinder mounting gasket

Dual-circuit master cylinder mounting gasket for foot of brake master

NZ$ 4.00
37H8128 RH 8.4" brake caliper

New right-hand side brake caliper for use with 8.4" disc brakes as fitted to 12" wheeled 1275GT, post 1984 mini and all Rover Minis

NZ$ 250.00
37H8129 LH 8.4" brake caliper

New left-hand side brake caliper for use with 8.4" disc brakes as fitted to 12" wheeled 1275GT, post 1984 mini and all Rover Minis

NZ$ 250.00
3H2424 Brake pipe 3 way connector

Brake pipe fitting found on the firewall and subframe of some models

NZ$ 42.00
3H2428 3/8" bleed nipple

3/8" bleed nipple. Used on calipers, twin-leading front cylinders, clutch slaves and various piping applications. Sold each.

NZ$ 4.00
3H500 3/8" copper washer for clutch & brake hydraulic connections

Copper washer for clutch & brake hydraulic connections. Creates seal from clutch slave to flexi hose, front brake cylinder/caliper to flexi hose etc

NZ$ 1.50
513123A Brake & clutch master cylinder plastic cap

Plastic cap for all clutch master cylinders and single-line brake master cylinders.

NZ$ 12.00
53K1048 Brake caliper retaining bolt

Caliper mounting bolt used on Minis with 7.5" Cooper S or 8.4" disc brakes. Sold each.

NZ$ 3.80
ACA5522 Handbrake cable fairlead

Metal guide plate holds the sealing pad to keep dirt and water from entering the car where the cable(s) pass through the transmission tunnel. Use two (2) per car to 1976, one after 1976. Use rubber sealing pad 21A385. Sold singly

NZ$ 7.00
ALA6505 Master cylinder base plate for tandem master cylinders

Master cylinder base plate & bracket for engine stabiliser. This is for cars fitted with a tandem brake master cylinder. Use with NAM9197 gasket. See 14A6733 for cars fitted with single circuit master cylinders.

NZ$ 49.00
Back Order

BHA4661 Master cylinder extension

Extension filler neck to fit clutch and single system metal brake master cylinders. Introduced in the 1960s by the Special Tuning department. The translucent plastic allows easy viewing of the fluid level, ideal for race cars. Note: does not fit modern plastic-body cylinders, only the original tin bean can type

NZ$ 38.00

Backorder
C16062A Hydraulic brake switch

Hydraulic brake light switch which screws into a fitting on the front subframe at the right side. This system was used up until 1976, when the switch was moved to the pedal. If your Mini uses this component, you should keep an extra of this part in your spares, so you can keep driving safely and legally.

NZ$ 25.00
Back Order

C-8G8995GREEN EBC Green Stuff brake pads for 7.5" brakes

Uprated EBC Green brake pads for 7.5" brakes for fast road and competition use. These pads give great braking and produce less brake dust which is great on cars with alloy wheel. Brake pad retaining pins to suit are PS610241

NZ$ 145.00

Backorder
C-AHT16GREEN EBC Green Stuff brake pads for 8.4" brakes

Uprated EBC Green brake pads for 8.4" brakes for fast road and competition use. These pads give great braking and produce less brake dust which is great on cars with alloy wheel. Brake pad retaining pins and shims to suit are GBK1027

NZ$ 155.00
Back Order

C-AJJ4028MS Cooper S disc brake kit

Kit containing all the parts required to convert a drum brake mini front end to Cooper S 7.5" discs. Designed to fit under 10" wheels but will also work with 12" or 13" wheels

Backorder
Back Order

C-AJJ4034 Mini GT disc brake kit

Kit containing all the parts required to convert a drum brake mini front end to 1275GT 8.4" discs. Designed to fit 12" or 13" wheels only

Backorder
Back Order

CLZ409 Handbrake cable clevis pin

Clevis pin to attach the rear of the handbrake cables to the actuating levers on the brake backing plates. Sold singly

NZ$ 4.00

Backorder
CLZ512 Master cylinder clevis pin

Clevis pin to connect brake & clutch master cylinders to pedals

NZ$ 4.50
CMZ407 Brake drum retaining screw

Brake drum retaining screw for standard 21A22 drums. Sold singly

NZ$ 0.90
CMZ422 Brake drum retaining screw for Cooper S drums

Brake drum retaining screw for GBD106 Cooper S brake drums. Sold singly

NZ$ 2.00
ENJO-1039 Wheel stud long for Cooper & GT brake drums

These were the stock rear wheel studs for 90s cars with the "Sportspac" option 6X13" wheels, but they can be fitted to ANY Classic Mini as needed to allow for wide rear drums, custom wheels and/or wheel spacers. These have a shank length of 2 3/8" (58mm) and about 3/4" (19mm) of thread.

NZ$ 6.00
ENJO-1040 Wheel stud extra long

This is the longest wheel stud available for the Classic Mini- 3.125" (78mm). It should only be used when running 3/4" or larger wheel spacers in special applications. Note that these will NOT fit most front disk brake cars and are intended primarily for use on the rear with wide rear drums AND wheel spacers. 3.125" is length of shaft, not including the head. Threaded portion approx. 1.125"

NZ$ 7.00
Back Order

FAM628 Handbrake cable connector

Handbrake cable connector for MK4 on cars. Connects the single cable to the handbrake lever

NZ$ 24.00

Backorder
FAM7821 Brake pressure limiting valve

Firewall mounted pressure reducing valve. Introduced in September 1978 and used until the end of production in 2000. This reducing valve is not owner serviceable and is only available as a replacement assembly

NZ$ 336.00
FAM9270 Tapered CV collar

Tapered collar which fits behind the large (1-5/16") nut used on 7.5" Cooper S and 8.4" disc brakes. Must be in place and in good condition to maintain proper torque of the castle nut. Sold singly

NZ$ 15.00

Parts Enquiry

MINIBITZ

LINKS

VISIT US